Wireless Router Range Extender

 Wireless router range extender can be used at home when there is no good connectivity from the home internet wireless router to all the rooms. This router has 2.4 and 5 GHz WiFi channels. There are a couple of antennas, the polarization of which can be changed from vertical to horizontal and anything in between. Signal LED lights up in blue colour when good signal is being received from the router. If not, it becomes red. There is also an RJ 45 LAN port on the lower side of the range extender, which can be used to connect to the internet router through a local area network cable. Then the range extender can be programmed as a WiFi hotspot from which other devices can connect to the internet provided by the internet router. This is useful if you can wire a LAN cable from ground floor where the router is kept and the first floor or higher floors where the range extender is to be used. Mode change can be done using a linked app installed in a mobile phone.



Comments

Post a Comment

Popular posts from this blog

Six Button Wireless Mouse vs Three Button Mouse

Image
 When I started using computers long back, mouse had only two buttons, a left and a right button. Then came three button mouse with an extra scroll button. I have read that there was also a single button mouse, but I have not seen one. Now here is a six button mouse, that too a wireless mouse with a USB-A Nano Dongle and 2.4 Ghz wireless connection. In the earlier era, mouse had a rolling ball which would gather dirt and sometimes stop functioning well. Now we have optimal mouse which uses a red light source and an optical sensor instead of the rolling ball. The wireless mouse works on a single 1.5 V, AA battery with a projected battery life of one year!
Read more

Debut Ham Radio Technical Discussion Net on 7065 kHz, 1:45 am UTC (7.15 am IST)

Image
Started by calling CQ on 7065 kHz using my automated CQ call which I had described yesterday. VU3RFT joined first followed by VU2EHA. Had a good discussion on Center Fed and End Fed Dipole Antennas. VU2EHA and VU3RFT participated. All of us were using inverted V dipole antennas. VU2EHA had 40 and 20m dipoles on same mast. VU3RFT was using 1:1 current balun. I mentioned that I am using 40/10m center fed dipoles with 1:1 current balun. VU2EHA asked about 15m dipole. I suggested that the 40m dipole will work well on 15m as it is an odd harmonic. He mentioned a problem because his IC-718 does not have an autotuner. We lost propagation at around 7.35 am IST. Wonder whether there was a geomagnetic storm? Number of waterfalls on 40m band decreased very much at that time. Planning to try again tomorrow at the same time. SWLs can monitor at  http://vu3wew.ddns.net:8073/ , the OpenWebRX by VU3WEW, located about 10km from here and likely to pick up my signals very well. Being a WebSDR, it can be
Read more

Building a Tape Measure Yagi for LEO Satellite Operations

Image
 The Moxon Yagi which I have been using for my LEO Satellite operations had a Moxon rectangle for VHF and five UHF Yagi elements which were passively coupled to the VHF Moxon driven element. The gain was not that high when I thought of working SO-121 QRP satellite. VU2TEK had good success with his Tape Measure Yagi which motivated me to go for one. But I don't expect the same success as he was operating outdoors, pointing the Tape Measure Yagi in the direction of the satellite pass. I am planning to use only in a mast mounted fashion which will limit its usability for satellite passes to a short period of about 4 minutes. I have chosen the DK7ZB design which I have been looking at for a quite a long time. That design has 5 elements for VHF and 8 elements for UHF with a boom length of about 1.5m. First step was to get a wooden reaper to use as the boom. Earlier it used to be available in all electrical wiring accessories shops. But now with the usage of PVC channels for wiring, I w
Read more